A-Tech 5000 HP Order Form

Detailed Information - Order Form - Assembly Guide - Shipping Status

Standard features:

6061-T6 heat-treated aircraft grade aluminum chassis and faceplate
Faceplate machined for either slot or tray load DVD drive
Machined aluminum power button with switch and wiring
Machined aluminum eject button
Power status LED with wiring
Mounting bracket for up to two hard drives
DVD drive mounting brackets with cable routing guides
Stainless steel stand-offs to fit full-size ATX motherboards
Two 80mm plated fan grills with screws (fans not included)
Plated I/O slot cover plates
Low-profile rubber feet
Hardware kit with all screws needed for installation
Complete set of hex keys to work on your case
Fine hand-sanded finish
Black or Silver (clear) anodized finish
Requires 2U size power supply
Width= 17.50", Depth= 11.00", Height= 5.63" (less feet)

A-Tech 5000 HP Heatsink Case .... $445 + options (select below)

Basic Case Faceplate Styles

Full-size slot-load

Faceplate is machined to fit a full-size slot-load DVD drive. This drive takes up more space inside the case than a slim-line drive below. Eject button is located in the lower right.

Compatible drives:

Pioneer 120S

Slim-line slot-load

Faceplate is machined to fit a slim-line slot-load DVD drive. This type of drive takes up less space inside the case and allows for larger CPU heatsinks and fans. Eject button is located in the lower left. Includes the special drive mounting brackets and hardware.

Compatible drives:

Panasonic UJ-825-B
Panasonic UJ-845-B
Panasonic CW-8123
Panasonic CW-8124-B
Pioneer DVR-K04L
Pioneer DVR-K05

Tray-load faceplate

Faceplate is machined to match the opening required for a tray-load DVD drive. Included is a matching aluminum DVD tray cover plate to attach to the front of your drive tray. The tray cover plate is finished to match the rest of case for a seamless appearance. Maximum tray door size is .875" x 5.438".

Select Faceplate Style:

Full-size Slot-load

Slim-line Slot-load - add $25

Tray Load - add $25

Case Finish

Faceplate Color

Black case with black faceplate

(3000 case shown)

Black case with silver faceplate

(6000 case shown)

The aluminum case and all aluminum brackets are treated by a anodizing process for corrosion protection and a long lasting uniform finish.

The rear portion of chassis is black anodized. The faceplate and buttons can be either black or silver.

Black Faceplate
Silver Faceplate

Laser Etched Logo Graphics

Laser Etched Logo Samples

(Shown: clear on black, black on clear)

Faceplate is laser etched with custom graphics and lettering during the anodizing process. Graphics can include company logo, button labels, system specs, and warning labels. Artwork to be provided by customer. Artwork should be in a vector format for best results. Approximate pricing:

Clear lettering on black case ($150)
Colored lettering on silver or black case ($175)

Contact A-Tech for price quote. Normally you can run about (10) faceplates for the same minimum charge, then a nominal fee per plate.

No Logo
With custom laser etched logo graphics

Face Plate Options

Touch Screen Mounting

Touch Screen Faceplate

Important Note: Hard drive mounting is limited with the Touch Screen option. Case can be configured with either one or two hard drives. With a full size DVD drive, only a single hard drive can be mounted sideways on the side panel above PCI slot 6. When a slim-line DVD drive is used, a second hard drive can also be mounted in the location above the power supply. When using the taller 400w PS, only one hard drive can be installed on side panel with either DVD drive.

Faceplate is machined with a cutout to fit a Xenarc 700TS LCD Touch Screen. The display can be used for operator input, previewing movies, or as a windows desktop. Push button controls turn display on/off and for control brightness, contrast and display position settings. Touch screen display not included.

Display Details - Installation Guide

Touch Screen style faceplate
Right-side power button and LED
Machined push button monitor controls
Monitor LED pin hole
Mounting hardware

note: VFD Display and DVD Control Buttons cannot be combined with the Touch Screen option

No Touch Screen Mounting
With Touch Screen Mounting - add $75

Xenarc Touch Screen Display

Xenarc Touch Screen Display

A-Tech Fabrication is now authorized by Xenarc to install their touch screen displays into our cases. The display will still have the full warranty from Xenarc. It will also include a special power cable to allow you to connect it to the power supply inside the case. The case will be shipped with the display installed into the faceplate. You must also purchase the touch screen mounting option above. If you purchase your own display, we will need to know which type of push button switch it has. The newest shipping units have a shorter button which requires our button inserts to be longer. There are pictures of the old buttons in the Installation Guide

Includes:

700TSV Display
VGA/composite video cable
USB input cable
AC power adapter
12v power supply adapter cable

No Xenarc Display
With Xenarc Display - add $400

VFD or LCD Mounting

VFD with blue filter and blue power LED

Faceplate is machined with a cutout to fit a Matrix Orbital 4x20 display. Can be used with or without tinted filters. Includes mounting hardware and spacers. Display not included.

Supported models:

VK204-25 (serial)
VK204-24-USB
LK204-25 (GW, WB, IY)

With VFD/LCD Mounting - add $35

note: VFD/LCD display mounting cannot be combined Touch Screen display option.

IR Receiver Mounting	UIRT receiver installed
Faceplate is machined with a cutout to fit a IRman or USB-UIRT infrared receiver. Includes mounting shelf, hardware, and adhesive strip. IR receiver not included.
No IR receiver mounting With IRman mounting - add $25 With USB-UIRT mounting - add $25

USB/Firewire Ports

USB/Firewire Port

Face plate is machined with cutout to fit a USB/Firewire adapter. Features two (2) USB ports and one IEEE 1394 Firewire port.

USB/Firewire port adapter
Universal cables
Mounting hardware
Instructions

NOTE: The USB/FW option can now be installed with the PowerMate option. The location of the USB/FW port will be in the space between the reset button and the DVD control buttons. See Picture

No USB/Firewire Ports
With USB/Firewire Ports - add $45

DVD Push Button Controls	Inside of case shows PowerMate, UIRT, DVD buttons, and VFD display.
Face plate is machined with cutouts to fit five custom machined push buttons. These buttons can be programmed to control software such as a DVD player. Button assembly comes pre-wired with header connector. This connector plugs into to the keypad connector on the Matrix Orbital displays such as the VK204-25 or similar displays with a keypad input connector. Includes five (5) machined aluminum buttons, five (5) momentary switches, wire harness, mounting rail and hardware. note: DVD Push Button Controls cannot be combined Touch Screen option
No DVD Push Button Controls With DVD Push Button Controls - add $75

PowerMate Control Knob Mounting

Face plate is machined with a cutout to fit the PowerMate control knob. Designed to fit the Griffin Technology PowerMate controller and input device (not included). This knob can be programmed for a number of tasks such as volume control and scrolling through menus. PowerMate knob not included. The PowerMate from Griffin is available in black or silver to match the case.

NOTE: The USB/FW option can now be installed with the PowerMate option. The location of the USB/FW port will be in the space between the reset button and the DVD control buttons. See Picture

No PowerMate Mounting
With PowerMate Mounting - add $45

Reset Button	Reset Button
Face plate is machined with a cutout to fit a machined aluminum reset button. Includes machined aluminum button, momentary switch and wire harness.
No Reset Button With Reset Button - add $25

Power LED
Standard case comes with a basic green power LED. A optional blue LED is available for a different look.
With Green LED With Blue LED - add $5

Machined Billet Aluminum Case Feet

Enhance the appearance of your case with these machined billet aluminum case feet. The standard rubber feet fit inside these aluminum feet and can be upgraded later.

With Standard Rubber feet

With Black Aluminum Case Feet - add $30
With Silver Aluminum Case Feet - add $30

Shipping and Ordering Information

These cases are custom made to your order. You may add additional options after work on your case has begun, however some changes may affect shipping time. If there is a custom option you would like to have that is not listed above, please contact us for a special quote. Options can also be added to your case at a later date, you only pay for the option plus a small refinishing fee.

Please read:

Atech Fabrication Warranty, Terms of Sale, and Refund Policy

When will the case ship?

See Ordering and Shipping Status for current ordering batch and shipping dates. Orders are shipped in the order they are received. The exact ship date may vary plus or minus two weeks. Typical lead time is four to eight weeks.

A-Tech 5000 HP Heatsink Case .... $445 + options

Please select options above before adding to cart. Before checking out, be sure to add any additional accessories below so that they can be shipped with your case.

A-Tech 5000 HP Accessories

Enermax 400 Watt Power Supply

This unique power supply from Enermax features a 80mm cooling fan on the front and a 60mm fan on the back. The fans can be slowed easily since their cables are plugged into on-board connectors inside the power supply similar to a motherboard fan connector. To reduce noise, Fan Speed Cables can be connected to the fan cables.

Note: Features higher +3.3v and +5v output for high demand systems.

Detailed specifications

400 Watt Power Supply

Modified 400 Watt Power Supply

The modified version has the internal fan speeds reduced for less noise. Both fans are slowed internally by using a simple fan extension cable with inline resistor. The larger 80mm front fan uses a 68ohm cable, while the smaller rear fan uses a 100ohm cable This combination has been fine tuned for optimum airflow with the least amount of noise.

Mass-Air-GPU Heatsink System

Silent, high performance heatsink system
Works with ATI Radeon video cards
High flow heatsink with copper heat spreader
Formed aluminum high flow air duct
Two mounting screws with preload springs

More Details

DVD Power Extension Cable
Due to the design of the door mounted DVD drive, a longer IDE power cable is needed. This cable is 14" long. For advanced users, another option is to extend the existing cable by splicing in a longer cable. $4.00

IDE Data Cable for DVD drive
Due to the design of the door mounted DVD drive, careful routing of the IDE data cable is required. The case includes cable clamps for routing a round IDE cable. The cable you use must have the bulky plastic boots removed for clearance. Round IDE cable, black 24" long single device Ultra DMA (ATA 133/100) 40 twisted pairs, 30 AWG Foil shield, PVC foam skin insulator Bootless 40-pin connectors
$10.00

Fan Speed Control Cable

The fans used in this case are the slowest speed available in a 70mm size. However, I prefer to run them even slower for reduced noise. Stock fan speed is 3300 RPM, this speed is fine for remote installations where noise is not a concern or where maximum cooling is desired. Advanced users can easily make/modify their own cables. Cable is just a standard fan extension cable with a resistor installed inline to reduce the current to the fan.

Note: There are many variables to optimum fan speed. You may want to run the fans faster with a hot video card. A cool running system can run the fans at slower speeds. For quiet cooling of your Radeon, see the Mass-Air Heatsink System.

Recommended fan speeds:

00 ohm = 3300 RPM (>3 GHz)
33 ohm = 2500 RPM (2.8 - 3 GHz)
47 ohm = 2300 RPM (2.5 - 2.8 GHz)
68 ohm = 2000 RPM (2.0 - 2.5 GHz)
82 ohm = 1600 RPM (1.8 - 2.0 GHz)
100 ohm = 1300 RPM (<1.8 GHz)

For lower noise, slower speeds can be used. Get a few sizes to see what works best in your system.

Automatic Fan Speed Controller
This Fan Speed Controller is compact in size for easy mounting in any location. Linear response curve for smooth ramp up. Load stabilized output for consistent speed. 12 volt start-up circuit spins fan at full speed during start up to ensure reliable operation. One controller can be used with two case fans using a fan splitter cable. Most motherboards can handle the current of two small fans per connector. Typical speed range is around 1700---2500 RPM. If you want to constantly run your fan at a precise RPM- get the fan speed cable instead.
$15.00

Fan Splitter Cable
Use this cable to connect two case fans to a single three pin header. Allows two fans to be used with one fan speed controller. 3-pin connectors for fans with tach signal. 12" length for extended reach.
$3.00


Home	HTPC Cases	Accessories	Antennas	Support	Contact	Checkout
Copyright © 2005 A-Tech Fabrication Company. All rights reserved.